Red Sonja – Leg Bands

The Red Sonja leg bands were constructed out of Worbla(*) , craft foam, elastic, and some leather trim. This was my first experience working with worbla and it was a lot of fun. Definitely understand why everyone loves this stuff! 

The bands ended up being about 1.5″ x 15″, enough to wrap almost the entire way around the client’s leg, but not quite. The pattern was free handed and roughly based on the cosplay reference I found on Deviant Art. I was going for a sort of hammered steel look.  The core is two layers of 3mm craft foam.  The bottom layer is solid, and the top layer has the cut outs.  I glued them together using regular PVA (elmer’s) glue and then covered them in Worbla.

Red Sonja Leg Band Pattern Red Sonja Leg Band Foam and Worbla

Actually wrapping the bands was a learning experience.  Worbla actually “stretches” a little, because once it is malleable it can be pulled.  I found that it was best to cut the worbla slightly smaller than necessary so that once it was warm I could kind of bring the edges together to seal them.  If there is too much overlap or you do not cut enough darts out on curves, you end up with lumpy bits that are difficult to smooth.

I used a darice embossing heatgun(*) that I picked up at Joann to heat the worbla.  To protect my floor, I used a 12×12 inch tile that was leftover from the house.  As the worbla heats, it will darken a little.  If you heat it up too much in a small area it can start to bubble.  After a while you learn the right amount and surface area to heat.

After doing a rough wrap with the worbla, I continued to soften it and work it into the depressions created by the foam. The round head of a pin worked surprisingly well to help squish it into the edges.  It was also useful to poke a hole in the worbla and let air out if bubbles did form.

Red Sonja Leg Band Wrapped

Then I added D rings using worbla scraps as fasteners. The rings move freely once the worbla cooled down. Then I heated and bent the band into the shape I wanted

Red Sonja Leg Band D Ring Attachment Red Sonja Leg Band Bent

After the bands completely cooled and hardened, I covered the front and backs with PVA glue to smooth out the surface a little bit.  Then came painting. First I brushed on a layer of black acrylic, followed by a metallic silver spray paint from Krylon.  After that dried, I dry brushed some black back in before finishing with a gloss clear coat.  The look I was going for was more cartoon/comic than realistic, so I wasn’t super detailed.  I just wanted there to be some high and low tones to make the pattern pop a little more.

Red Sonja Leg Band Black Base Coat Red Sonja Leg Band Silver 1 Red Sonja Leg Band Silver 3

To fasten them to the legs, I decided to go with an elastic/velcro contraption, which was covered by a silver leather scrap I found at Joann.  I actually wish I had done this differently.  I wanted something that looked like it was “one” piece and didn’t want any elastic or modern hardware showing. The silver piece is meant to be trimmed and lie flat once the elastic is taught against the skin, to make the transition between the band and elastic more seamless.  This didn’t work out as well as I hoped it would, and I wish I had gone with a more traditional method, or used some leather scraps and a D ring.  

Red Sonja Leg Band Attachment Red Sonja Leg Band Leather

And here is the final product!

Red Sonja Leg Band Finished

 

(*) affiliate link

Red Sonja – Gloves

The first thing that I worked on for Red Sonja was the gloves.  I’ve never made gloves before, so I did a lot of googling before deciding on an approach. Originally I wanted to use a heavily interfaced stretch pleather, but I couldn’t find the right thing at the store, and my samples came in too slow from Spandex House. Plus after making a mockup in some spare pleather I had laying around I decided it would be much too hot. 

Instead, I ended up with a coffee colored pigskinsuede split from Tandy, thinking it would breathe more. According to the site it is a 1 – 1.5 oz hide and approximately 6 sq feet, although I feel like mine was closer to 4. For the pattern I used Butterick5695 because it was laying around in my stash. I knew all those 99 cent pattern sales I hoard would come in handy for something!

The first thing I did was create a mockup of the glove using some old pleather that I had left over from my batman-inspired dress.  At the end I had something that actually looked like a glove!  It was pretty cool.

First Glove Prototype Back

Red Sonja’s gloves have a pretty distinct flare to them, as well as a cutout.  The total flare of the cuff was determined by slashing and spreading the prototype, then filling in the space with masking tape.  The total circumference ended up being just shy of 15 inches.

First Glove Prototype Cuff

The only other modification I made to the Butterick pattern was to shorten the thumbs by 1/4″.

When laying out the pattern I was trying to lay the fourchettes on the thinnest part and the cuffs/gauntlets on the thickest.  This might have make a small difference, but to be honest the whole hide is pretty thick so it was still difficult to sew.

Red Sonja Glove Layout

Even with glove needles sewing the fourchettes in was very very tough. I was able to do machine sewing on some of it, but the corners and finger tips had to be hand sewed.  Even using a three-sided glove needle and thimble, this took forever!

Red Sonja Glove Fingers

I’m really pleased with the way the cutouts came out.  For the cuffs, I used fusible interfacing on the lining (which was a polyester whatever from Joann), then reinforced the cutout with another piece of interfacing after I folded the edges in. The Lining was sewn to the top edge after the rest of the glove was constructed, then turned to the inside.  I sewed around the cutout to keep the lining and outer cuff together, then very carefully trimmed the leather on the outside.

Red Sonja Glove Cuff - Lining Cutout CloseupRed Sonja Glove - Lining Cutout Interfacing CloseupRed Sonja Glove Cuff - Lining Cutout FinishedRed Sonja Glove Cuff Lining

Overall I’m pleased with how they came out. The fingers are not as even as I would like them to be, but once they are on the flaws don’t show as much. I mean.. I made GLOVES! For some reason that is so much more satisfying than the normal things I make.

The “glove stand” is just a piece of foam board with a cut up pool noodle from the dollar store hot glued to it.

Red Sonja Glove Finished Back Red Sonja Glove Fist Red Sonja Glove Inside Cuff Red Sonja Gloves Finished Back